Search results

  1. A

    VIC Sold

    Drop to 1000
  2. A

    VIC Sold

    price adjust for value :P 1000-1500
  3. A

    VIC Sold

    Item: Giant Trance X1, 26", Large frame(18") Location: Melbourne, Doncaster Item Condition: Excellent Reason for selling: Other hobbies have taken over Extra Info: Only thing stock is the frame, forks and rear suspension Forks and rear suspension have just had a full service, in...
  4. A

    2008 Giant Trance X1, first mtb build

    Just had a tune up ride out on the yarra trail, bike is riding a treat, them wheels are heavy though, had an Ivanhoe jump session as well :P So happy with the build
  5. A

    2008 Giant Trance X1, first mtb build

    picture update
  6. A

    [VIC] Shimano Saint M810/M820 RH Lever

    Item: Shimano Saint M810 RH Lever or M820 RH Location: Melbourne, Eastern Suburbs Price Range: $50, unsure as to value, open to higher
  7. A

    Shimano Saint M810 Bleed problem

    Will get supplies tomorrow from lbs and report back
  8. A

    Shimano Saint M810 Bleed problem

    Just purchased a pair of second hand shimano saint m810 brakes the method I used to bleed is as follows Prep: remove caliper from frame remove pads insert bleed block level off lever unscrew reservoir cap insert tube that came with shimano bleed kit to bleed nipple on caliper Bleed Process...
  9. A

    2008 Giant Trance X1, first mtb build

    Update: Replaced deore shifters and deore rear mech with saint m810 shifters and rear mech (short cage)
  10. A

    Found

    150 for the lot?
  11. A

    2008 Giant Trance X1, first mtb build

    36, starting to regret it, will most likely end up going 30
  12. A

    Found

    item: Shimano Saint 9 speed rear mech Location: Melbourne Price: 50-100 depending on condition
  13. A

    2008 Giant Trance X1, first mtb build

    Frame - 2008 Giant Trance Rear shock - Fox RP2 Front shock/fork - Fox float RL 32 F120 Handlebars - Truvativ 710mm wide Stem - Truvativ Holzfeller 50mm Grips - Jetblack Front brake - Shimano Saint M810 Rear brake - Shimano Saint M810 Cranks - shimano zee 170mm Pedals - Nukeproof Proton Rear...
  14. A

    Sun ringle rear conversion axle 12mm

    Wheel set just arrived as well as the conversion axle, was a good snug fit
  15. A

    Chain Reaction Cycles Custom Wheel Builds

    Update: Arrived 30th june Seems a solid build, will update when ridden
  16. A

    Chain Reaction Cycles Custom Wheel Builds

    Order update: Ordered 17th (3pm) Dispatched 24th (2:50am)
  17. A

    Biggest jump, gap, drop or whatever photos!

    From a few years back on the yarra trail near westerfolds i used to think the whole handlebar turn thing looked cool
  18. A

    Shimano Hub service

    hmmm just looked up the tech doc, 13 ball bearings on that side and it seems like there is only a ball retainer on the non drive side, wuhhhhhh?????? why why why
  19. A

    Shimano Hub service

    that was my first concern, does not seem like there is enough ball bearings i will check up with shimano how many there are supposed to be and open it back up tomorrow at some point
  20. A

    Shimano Hub service

    just had a quick play with the tension, when its relatively loose it spins well, cant check for lateral play atm its less than finger tight however, will this be a problem? cheers for the advice
Top